The TinySensor is a ATTiny84 based multi-purpose board. It is designed to primary serve as a low power, battery operated wireless remote sensor that will measure and transmit data to a remote base at regular intervals. For the purpose, there is a dedicated temperature sensor port (intended for DS18B20 one-wire temperature sensor bus) and a configurable voltage divider.
Schematic and board TinySensor v1.4_rev3
Numerous applications and hardware configurations are possible, some examples include
- Temperature sensing
- Air Humidity Sensing
- Light Intensity sensing
- Current sensing (for power monitoring)
- Soil Moisture sensing
- Water flow sensing
- Switch position sensing
..and many more, limited by your imagination only. See my projects tagged with Attiny84
The module has on-board RFM12B transceiver module, so it is able to communicate with other modules in the wireless network.
Additionally, there is a SD card pin connector, that allows storing measurement data on a SD card, in really remote locations that may be useful option.
There is a Jeelabs JeePort, so you can benefit from all JeePorr compatible sensors /libraries out there
A 3.3V FTDI connector can be used to power the board and serial bi-directional debugging (no programming yet)
A CR2032 battery slot can be used to power the board when the application permits ultra-low power mode and long intervals between transmissions of data.
A Raspberry Pi connector allows plugging the TinySensor directly on a Raspberry Pi and using UART to communicate between the two modules. A good example usage is the RFM12b to Raspberry Pi serial gateway project.
Building the TinySensor is pretty much trivial. Start with the lowest profile components and gradually add them in the order of height, this way the taller components won’t stand in the way.
I usually start with the 10K resistors that keep the ATtiny84 reset and RFM12B’s Slave Select lines pulled up. If you will not use the ISP for programming, these two resistors may be omitted.
If you intend to use the DS18B20 temperature sensor, you need to solder the 4K7 resistor that keeps the data line pulled up. I prefer to add headers instead of soldering the other resistors, so that I can change configurations on the run.
Next, solder in the two decoupling capacitors. These are ceramic and orientation doesn’t matter.
I then solder the RFM12B module on the bottom of the PCB. The orientation of the RFM may be a bit tricky to figure at first. The crystal needs to go on the inner side of the pcb. Apply a small amount of solder on one of the pins so that it affixes the whole module. Adjust if necessary so it is in the middle of the footprint. Once positioned, solder carefully all connections. I hold the soldering iron a bit longer when soldering the RFM12Bs so that solder falls in the bottom of the module as well. Make sure there is solder on the top of the pad as well, I have had issues where I didn’t have enough solder applied. The antenna needs to be 82mm for 868Mhz modules.
You can now solder a 14 pin socket (or the ATTiny84 directly, if you need low-profile, but the socket is recommended for most uses) and the ATTiny84. The silk screen shows the correct orientation of the socket and the chip.
Next is the 6-pin ISP connector, if you will use it to program the ATtiny.
This is the basic configuration to get you started
Check this post on how to setup Arduino IDE for working with ATTiny84.
Check the code repository for TinySensor on github.
Using the TinySensor with a Raspberry Pi
Note: Prior to doing any further work, please backup Raspberry Pi’s SD card.
The TinySensor has a dedicated port sized 2×5 pins, that allows it to be plugged on a Raspberry Pi. It will get its power from the 3.3V line and will connect Pi’s UART TX and RX TinySensor’s PA3 and PA7 respectively.
When plugging the TinySensor on the Raspberry Pi, make sure of the following:
- The TinySensor board is held on the Pi by the 2×5 pin header only. If pressed, it may contact the Pi’s other components. I apply a small amount of hot glue silicon on two points, where potential contact between the TinySensor and the Raspberry Pi may occur, you can use isolation band as well. These points are the FTDI connector (if soldered, the connections are close to Pi’s GPIOs) and between the ISP connector and DS18B20 port, so that the board doesn’t touch the large capacitor on the Pi:
- The TinySensor should not be powered from another source.
- Don’t plug FTDI cable directly in the FTDI port as it provides 3.3V too. You may use FTDI for serial debugging by connecting it with jumper wires, you need only GNS, TX and RX lines. Leave the FTDI power unconnected
- If you have the CR2032 battery installed, please remove it. If you have other batteries installed at the external battery connector, make sure they are disconnected
- If you have ISP programmer connected, please make sure it does not power the TinySensor. There is a jumper on most ISP programmers that disconnects the power line
- Make sure Raspberry Pi’s UART is disconnected from the console and available for programs to use it
- First, make a backup of the cmdline.txt file
sudo cp /boot/cmdline.txt /boot/cmdline_backup.txt
- Next, edit it to remove references to Pi’s UART (ttyAMA0)
sudo nano /boot/cmdline.txt
- Originally it contains this
dwc_otg.lpm_enable=0 rpitestmode=1 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait
- Edit it to look like this
dwc_otg.lpm_enable=0 rpitestmode=1 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait
- Press Ctrl+O to save, then Ctrl+X to exit
- Next, type “sudo nano /etc/inittab” and comment (or remove) the line (towards the end of the file)
2:23:respawn:/sbin/getty -L ttyAMA0 115200 vt100
- Restart the Raspberry Pi by typing “sudo reboot” so changes take effect
- I use minicom to view the serial data
sudo apt-get install minicom
And to run it at 9600 baud (or change that to whaterver baud you used on TinySensor’s side:
minicom -b 9600 -o -D /dev/ttyAMA0
Tip: you may use “sudo minicom -s” to store these settings as permanent
Page views: 6133